1. Bathroom machine tool is composed of main engine, hydraulic transmission system and electrical control system.

2. The control system of the equipment has three working methods: manual, semi-active and active. The working method is selected by the conversion switch, and the touch screen is assembled and controlled. Semi-active methods are divided into "with ejection" and "without ejection", "with exhaust" and "without exhaust" and "micro-opening" process actions for selection, and the number of exhaust can be adjusted.

In the process of "no ejection" operation, an outside "ejection" button and a "return" button are arranged on the operating plate. There are four groups of independent buttons (pressure compensation variable pump is selected for ejection speed).

External ejection: This machine is equipped with independent double ejection and double core pulling equipment, and synchronization system of ejection equipment in the mould, which makes the opening of the mould stable and reliable. (Six sets of M16 independent joints in die ejection equipment) Presses are equipped with organic and external "ejection" and "return" oil system interfaces, which are connected with high-pressure hoses (Party A supplies the pressure of each press's external oil circuit and related connection standards, etc.).

3. The cartridge integrated valve is used in the main hydraulic control system of the equipment. The system has compact structure, reliable action, strong anti-pollution ability, small fluid resistance, convenient repair and long service life.

4. PLC programmable controller and touch screen are selected in the electrical control system of the machine, which can end all kinds of process action cycle of the machine tool. The system makes the manipulation more sensitive and the action more accurate and reliable. It can conveniently preset the parameters such as the stroke and pressure of the slider on the screen. It also has a movable operating table.

5. The main cylinder seals are all made of Baoli excellent sealing rings, which greatly prolongs the service life of the seals and avoids the leakage of oil from the cylinder mouth. Make repairing and replacing seals more convenient.

6. The main power system of the equipment and the filling tank are placed on the top of the main engine, which can reduce the occupied area of the machine.

7. The equipment is equipped with safety repairing channels, the mobile operating platform is equipped with two-hand operation buttons, the hydraulic system is equipped with overload protection equipment and hydraulic support insurance circuit. It can effectively protect the safety of machines and operators. It meets the requirements of hydraulic press safety technical conditions.

8. The hydraulic system tank of the equipment is equipped with oil level indication, hydraulic oil filtration and circulation. Ensure that the oil temperature of the machine tool is between 15 and 45 degrees Celsius.

9. The equipment is equipped with many kinds of fault indicator lights and fault alarm functions, such as oil filter blocking, oil level indication, oil temperature and smoothness.

10. The equipment is equipped with an independent oil circulation filtration system, which can actively filter the oil in the tank to ensure the cleanliness of the oil.

11. Pressure control of press adopts share pressure control system, and can end digital flash and digital control. Pressure sensor is used for pressure measuring component, and share relief valve is used for pressure regulating control component. Pressure flashing is flashed through touch screen.

12. Slider stroke can end digital flash, digital manipulation, measurement and flash accuracy to 0.1 mm.

13. The equipment is operated by the assembly button of the electric operation box. Touch screen is set on the operation box. Selection switches and buttons are installed under the operation panel. All kinds of fault alarm lights and control surfaces are placed above.

14. Pressure retention of the system requires a pressure drop of less than 1 Mpa in 10 minutes, and no pump start-up is allowed. In the process action, there is an open-die blowing process action.

15. Install a pumping pump on the oil tank of the press (for injecting new oil into and discharging oil into the oil tank) and separate control buttons. At the bottom of the oil tank and on the oil pump, a 1-inch pumping pipe and an oil discharging pipe (1.3 meters above the ground, plus a quick-opening valve for each oil pipe).

16. External ejection: This machine is equipped with independent double ejection and double core-pulling equipment, and synchronization system of ejection equipment in the mould, which makes the opening of the mould stable and reliable.

17. Supplementary Pressure Equipment: After equipping with a new type of active energy-saving supplementary pressure system, it can end long-term pressure stability and consume little energy. The system does not give off heat.

18. Flexible pressure relief conversion equipment: The equipment has no impact in the process of speed and pressure conversion, which makes the equipment work smoothly and reliably.

19. Die matching equipment: The equipment has the function of pressure-free and slow downward movement. It does not damage the die when installing new or replacing the die, and protects the die greatly.

20. Segmental venting function: Exhaust is sometimes required before the press closes the mould, and there is a selection button on the touch screen to determine whether exhaust is needed at that time. The bleeding parameters can be set according to the process requirements, and the bleeding time can be divided into eight sections.

21. Sectional Pressure Holding Function: During the period of holding pressure, the surface quality of the parts can be improved by the active conversion of several stages of pressure. Generally, it can be divided into three stages.

22. Fast pressure function: It can reach the set pressure in a short time before the die closing of the press. Whether this function is the key to whether the parts can reach the A-level surface or not.